In inquiry list
Brass Male Flare Adaptor, Flare Fitting
Male Flare Adaptor, made for flared tubing on fuel, oil, air and gas lines. It joins a flared tube to a male thread. Ask us for the size list.

We are a manufacturer of brass flare fittings: adaptors, unions, tees, plugs, nuts and gas connectors for flared tubing. They go to distributors, equipment makers and gas and refrigeration suppliers.
In inquiry list
Male Flare Adaptor, made for flared tubing on fuel, oil, air and gas lines. It joins a flared tube to a male thread. Ask us for the size list.
In inquiry list
Female Flare Adaptor for flared tubing on fuel, oil, air and gas lines. It joins a flared tube to a female thread. Ask us for the size list.
In inquiry list
Flare Union. It joins two flared tubes, for flared tubing on fuel, oil, air and gas lines. Ask us for the size list.
In inquiry list
Solder Flare Adaptor. It joins a flared tube to a soldered pipe, for flared tubing on fuel, oil, air and gas lines. Ask us for the size list.
In inquiry list
Flare with Nut, made for flared tubing on fuel, oil, air and gas lines. It joins a flared tube to a pipe thread, with the nut attached. Ask us for the size list.
In inquiry list
Flare Plug. It closes a flared connection, for flared tubing on fuel, oil, air and gas lines. Ask us for the size list.
In inquiry list
Female 90 Degree Elbow, made for flared tubing on fuel, oil, air and gas lines. It turns a flared line 90 degrees and ends in a female thread. Ask us for the size list.
In inquiry list
Male Flare Tee. It splits a flared line and gives a male-threaded branch, for flared tubing on fuel, oil, air and gas lines. Ask us for the size list.
In inquiry list
Flare Tee for flared tubing on fuel, oil, air and gas lines. It splits a flared line into two. Ask us for the size list.
In inquiry list
Gas Connector, made for flared tubing on fuel, oil, air and gas lines. It connects gas lines to a thread. Ask us for the size list.
In inquiry list
Gas Connector with Barb, made for flared tubing on fuel, oil, air and gas lines. It connects a hose to a gas line, with a barb on one end. Ask us for the size list.
In inquiry list
Flare Nut for flared tubing on fuel, oil, air and gas lines. It is the nut that holds a flared tube against the fitting. Ask us for the size list.
01A flare fitting seals where the cone of the fitting meets the flared end of the tube, so that cone has to be clean and true.
02We cut it on CNC lathes, then check the angle and the thread on a vision measuring machine.

Cone angle and thread on a vision measuring machine.
The metal of each batch read by a spectrometer.
Seats checked by hand for rough spots that could leak.
Parts boxed by model after the hand check.
Most buyers stock flare fittings by type and size, in full cartons. Each model has its own carton, and mixed orders are welcome. The minimum order and lead time are written into every quote.



Send a drawing or a sample if you need a different length, a different thread, or a part for your own equipment. NPT versions can be made on request. If one of our models is close to your part, tell us the change and we will start there.
The two flare angles look alike but do not mix.
A 45° flare is the common SAE type, used for refrigeration, gas and automotive lines.

A 37° flare is the AN type, used in hydraulic and aircraft lines.

Check the angle on your tubing and your nut before you order. A flare joint seals metal to metal, so do not use thread tape on the cone.

the tube end is flared first. It gives a strong joint for gas, fuel and refrigeration, and it can be taken apart and remade.

a ring grips the tube, so there is no flaring tool. It is quicker, but the ring is usually used once.

Cut the tube square and remove the burr inside and out.
Slide the flare nut onto the tube, thread side facing the end.
Flare the tube end with a flaring tool, to the right angle.
Fit the flared end against the cone of the fitting.
Tighten the nut. Do not over-tighten, or the flare can crack.




No. The flare seals metal to metal.
Yes, if the flare is not cracked. If it is damaged, cut it off and flare again.
Tubing that can be flared: copper, brass, aluminum and welded steel.
Yes, on request.

Tell us the model, the flare angle and the quantity, and we will send a price and lead time. [询盘表单]
## 给您的备注
We reply by email.